View NCP781BMN150TAG_8870086.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2016 april, 2017 ? rev. 0 1 publication order number: ncp781/d ncp781 150 v, 100ma very high voltage linear regulator the ncp781 is a very high?voltage tolerant linear regulator that offers the benefits of thermally enhanced dfn6 3.3 x 3.3 package and is able to withstand continuous dc or transient input voltages up to 150 v. the device is stable with small 0.1 f ceramic output capacitors which allows smaller pcb design at space constraining applications. the devices featur es enable pin compatible with standard cmos logic. features ? wide input voltage range: 6 v to 150 v ? output voltage versions: fixed: 3.3 v, 5 v, 15 v adjustable: from 1.23 v up to 15 v ? 2.5% accuracy at room temperature ? very low quiescent current of typ. 25 a ? standby current: 1 a ? stable with a 0.1 f ceramic output capacitor ? very high psrr: 83/56 db@1/100 khz ? thermal shutdown and current limit protection ? available in thermally enhanced dfn6 3.3 x 3.3, 0.65p package ? ideal for harsh environments ? these are pb?free devices typical applications ? telecom, industrial ? bias power supplies, led lighting ncp781 adj c in c out r 1 r 2 1 uf 1 uf vin = 6 v ? 150 v vout = 1.23 v ? 15 v ncp781 fix in en out gnd c in c out 1uf 1uf in en gnd out adj vout = 1.5 v ? 15 v figure 1. typical applications vin = 6 v ? 150 v enable enable sen www. onsemi.com see detailed ordering and shipping information in the package dimensions section on page 13 of this data sheet. ordering information marking diagram dfn6 s suffix case 506df 1 781n = specific device code a = assembly location y = year ww = work week = pb?free package 781n ayww (note: microdot may be in either location) pin connection (top view) 1 2 ep 6 3 4 5
ncp781 www. onsemi.com 2 figure 2. simplified block diagram for adjustable version current limit & thermal shutdown in gnd vref en out ncp781 fix version figure 3. simplified block diagram for fixed version sen
ncp781 www. onsemi.com 3 table 1. pin function description pin no. dfn6 3.3 x 3.3 pin name description 1 in positive power supply input 2 en chip enable pin (active ?h?) 3 nc not connected 4 gnd power supply ground 5 out regulated output voltage 6 adj/sen output voltage adjust input (adjustable version), sense pin for output voltage sensing, connect to pin 5 (fixed voltage versions) ep ep ep should be connected to gnd potential absolute maximum ratings rating symbol value unit input voltage range (note 1) v in 150 v output voltage range (note 2) v out ?0.3 to 20 v v enable input range v en ?0.3 to (vin + 0.3) v v adjustable input range v adj ?0.3 to 5 v v output short circuit duration t sc unlimited s maximum junction temperature t j(max) 150 c storage temperature range tstg ?55 to 150 c esd capability, human body model (notes 3, 4) esdhbm 2 kv esd charged device model esd (notes 3, 4) esdcdm 750 v moisture sensitivity level msl 1 ? lead temperature soldering reflow (smd styles only), pb?free versions (note 5) t sld 260 c stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. refer to electrical characteristic and application information for safe operating area 2. the device has limited reverse bias protection. reverse bias protection feature valid only if (v out v in ) < 7 v. 3. this device series incorporates esd protection and is tested by the following methods: esd human body model tested per aec?q100?002 (eia/jesd22?a114) esd charged?device model esd capability per jedec jsd22?c101e latchup current maximum rating: 150 ma per jedec standard: jesd78 4. except in and en pins. 5. for information, please refer to our soldering and mounting techniques reference manual, solderrm/d table 2. thermal characteristics rating symbol value unit thermal characteristics, dfn6, 3.3 x 3.3 mm (note 6) thermal resistance, junction?to?air (note 7) r ja 125 c/w 6. refer to electrical characteristics, recommended operating ranges and/or application information for safe operating parameters. 7. values based on copper area of 645 mm 2 (or 1 in 2 ) of 1 oz copper thickness and fr4 pcb substrate.
ncp781 www. onsemi.com 4 table 3. electrical characteristics ? adjustable ?40 c t j 125 c; v in = voutnom + 10 v, c in = c out = 1 f, unless otherwise noted. typical values are at t a = +25 c. (notes 8, 9) parameter test conditions symbol min typ max unit input regulator operating input voltage v in 6 150 v output regulator reference voltage accuracy ?40 c t j 125 c, i out = 50 a 6 v v in 150 v ?3% 1.23 v +3% % reference voltage accuracy t j = 25 c, i out = 50 a 6 v v in 150 v ?2.5% 1.23 v +2.5% % line regulation 15 v v in 150 v i out = 50 a reg line 0.25 0.5 %vout load regulation reg load 0.4 0.8 %vout dropout voltage (note 10) 3.3 v 5.0 v 12.0 v 15.0 v v do = v in ? (v out ? (3%voutnom)) i out = 100 ma v do ? ? ? ? 4 4 4.4 4.7 6.5 7.0 7.5 9.5 v disable, quiescent and ground currents disable current v en = 0 v, v in = 150 v i dis ? 1 10 a quiescent current i out = 0 ma i q ? 25 55 a ground current i out = 100 ma i gnd ? 250 400 a enable pin current 1.5 v < v en < 150 v i en 500 na adj pin current 6 v < v in < 150 v, adj = v out i adj 5 na current limit protection current limit (note 11) v out = v outnom ? (10% v outnom ) i lim 110 ma short circuit current limit v out = 0 v, vin = 25 v i sc 220 ma enable thresholds enable input threshold voltage voltage increasing, logic high voltage decreasing, logic low high low v th(en) 1.5 ? ? ? ? 0.4 v psrr and noise power supply ripple rejection (note 12) v in = 25 v + 200 mv pp modulation v out = 1.23 v, cout = 1.0 f i out = 10 ma f = 1 khz f = 10 khz f = 100 khz psrr ? ? ? 83 75 56 ? ? ? db output noise voltage (note 12) v out = 1.23 v, v in = 150 v i out = 1 ma, cout = 1.0 f f = 100 hz to 100 khz v noise ? 130 ? v rms thermal shutdown thermal shutdown temperature (note 12) t sd ? 160 ? c thermal shutdown hysteresis (note 12) t sh ? 15 ? c 8. performance guaranteed over the indicated operating temperature range by design and characterization production tested at tj = ta = 25 c. low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 9. i out > 50 a at v in > 50 v 10. not characterized at v outnom < 3.3 v. 11. respect to soa 12. guaranteed by design and characterization
ncp781 www. onsemi.com 5 table 4. electrical characteristics ? 3.3 v ?40 c t j 125 c; v out = 3.3 v typical, v in = 13.3 v, c in = c out = 1 f, unless otherwise noted. typical values are at t a = +25 c. (notes 13, 14) parameter test conditions symbol min typ max unit input regulator operating input voltage v in 6 150 v output regulator output voltage accuracy ?40 c t j 125 c (v outnom + 10 v) v in 150 v ?3% 3.3 +3% v output voltage accuracy t j = 25 c, i out = 50 a (v outnom + 10 v) v in 150 v ?2.5% 3.3 +2.5% v line regulation 15 v v in 150 v i out = 50 a reg line 8.3 16.5 mv load regulation (note 16) v in = 13.3 v reg load 13.2 26.5 mv dropout voltage (note 15) i out = 100 ma v do 4.0 6.5 v disable, quiescent and ground currents disable current v en = 0 v, v in = 150 v i dis ? 1 10 a quiescent current i out = 0 ma i q ? 27 57 a ground current i out = 100 ma i gnd ? 250 400 a enable pin current 1.5 v < v en < 150 v i en 500 na current limit protection current limit (note 16) v out = v outnom ? (10% v outnom ) i lim 110 ma short circuit current limit v out = 0 v, vin = 25 v i sc 220 ma enable thresholds enable input threshold voltage voltage increasing, logic high voltage decreasing, logic low high low v th(en) 1.5 ? ? ? ? 0.4 v psrr and noise power supply ripple rejection (note 17) v in = 25 v + 200 mv pp modulation v out = 3.3 v, c out = 1.0 f i out = 10 ma f = 1 khz f = 10 khz f = 100 khz psrr ? ? ? 75 62 48 ? ? ? db output noise voltage (note 17) v out = 3.3 v, v in = 150 v i out = 1 ma, c out = 1.0 f f = 100 hz to 100 khz v noise ? 260 ? v rms thermal shutdown thermal shutdown temperature (note 17) t sd ? 160 ? c thermal shutdown hysteresis (note 17) t sh ? 15 ? c 13. performance guaranteed over the indicated operating temperature range by design and characterization production tested at tj = ta = 25 c. low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 14. i out > 50 a at v in > 50 v 15. characterized when v out falls 99 mv below the regulated voltage and only for devices with v outnom = 3.3 v 16. respect to soa 17. guaranteed by design and characterization
ncp781 www. onsemi.com 6 table 5. electrical characteristics ? 5.0 v ?40 c t j 125 c; v out = 5.0 v typical, v in = 15 v, c in = c out = 1 f, unless otherwise noted. typical values are at t a = +25 c. (notes 18, 19) parameter test conditions symbol min typ max unit input regulator operating input voltage v in 6 150 v output regulator output voltage accuracy ?40 c t j 125 c (v outnom + 10 v) v in 150 v ?3% 5.0 +3% v output voltage accuracy t j = 25 c, i out = 50 a (v outnom + 10 v) v in 150 v ?2.5% 5.0 +2.5% v line regulation 15 v v in 150 v i out = 50 a reg line 12.5 25 mv load regulation (note 21) v in = 15 v, 50 a i out 100 ma reg load 20 40 mv dropout voltage (note 20) v do 4 7.0 v disable, quiescent and ground currents disable current v en = 0 v, v in = 150 v i dis ? 1 10 a quiescent current i out = 0 ma i q ? 27 57 a ground current i out = 100 ma i gnd ? 250 400 a enable pin current 1.5 v < v en < 150 v i en 500 na current limit protection current limit (note 21) v out = v outnom ? (10% v outnom ) i lim 110 ma short circuit current limit v out = 0 v, vin = 25 v i sc 220 ma enable thresholds enable input threshold voltage voltage increasing, logic high voltage decreasing, logic low high low v th(en) 1.5 ? ? ? ? 0.4 v psrr and noise power supply ripple rejection (note 22) v in = 25 v + 200 mv pp modulation v out = 5.0 v, c out = 1.0 f i out = 10 ma f = 1 khz f = 10 khz f = 100 khz psrr ? ? ? 65 56 45 ? ? ? db output noise voltage (note 22) v out = 5.0 v, v in = 150 v i out = 1 ma, c out = 1.0 f f = 100 hz to 100 khz v noise ? 300 ? v rms thermal shutdown thermal shutdown temperature (note 22) t sd ? 160 ? c thermal shutdown hysteresis (note 22) t sh ? 15 ? c 18. performance guaranteed over the indicated operating temperature range by design and characterization production tested at tj = ta = 25 c. low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 19. i out > 50 a at v in > 50 v 20. characterized when v out falls 150 mv below the regulated voltage and only for devices with v outnom = 5.0 v 21. respect to soa 22. guaranteed by design and characterization
ncp781 www. onsemi.com 7 table 6. electrical characteristics ? 15 v ?40 c t j 125 c; v out = 15.0 v typical, v in = 25 v, c in = c out = 1 f, unless otherwise noted. typical values are at t a = +25 c. (notes 23, 24) parameter test conditions symbol min typ max unit input regulator operating input voltage v in 6 150 v output regulator output voltage accuracy ?40 c t j 125 c (v outnom + 10 v) v in 150 v ?3% 15.0 +3% v output voltage accuracy t j = 25 c, i out = 50 a (v outnom + 10 v) v in 150 v ?2.5% 15.0 +2.5% v line regulation 25 v v in 150 v i out = 50 a reg line 37.5 75 mv load regulation (note 26) v in = 25 v, 50 a i out 100 ma reg load 60 120 mv dropout voltage (note 25) v do 4.7 9.5 v disable, quiescent and ground currents disable current v en = 0 v, v in = 150 v i dis ? 1 10 a quiescent current i out = 0 ma i q ? 27 57 a ground current i out = 100 ma i gnd ? 250 400 a enable pin current 1.5 v < v en < 150 v i en 500 na current limit protection current limit (note 26) v out = v outnom ? (3% v outnom ) i lim 110 ma short circuit current limit v out = 0 v, vin = 25 v i sc 220 ma enable thresholds enable input threshold voltage voltage increasing, logic high voltage decreasing, logic low high low v th(en) 1.5 ? ? ? ? 0.4 v psrr and noise power supply ripple rejection (note 27) v in = 25 v + 200 mv pp modulation v out = 15 v, c out = 1.0 f i out = 10 ma f = 1 khz f = 10 khz f = 100 khz psrr ? ? ? 53 50 43 ? ? ? db output noise voltage (note 27) v out = 15 v, v in = 150 v i out = 1 ma, c out = 1.0 f f = 100 hz to 100 khz v noise ? 530 ? v rms thermal shutdown thermal shutdown temperature (note 27) t sd ? 160 ? c thermal shutdown hysteresis (note 27) t sh ? 15 ? c 23. performance guaranteed over the indicated operating temperature range by design and characterization production tested at tj = ta = 25 c. low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 24. i out > 50 a at v in > 50 v 25. characterized when v out falls 450 mv below the regulated voltage and only for devices with v outnom = 15.0 v 26. respect to soa 27. guaranteed by design and characterization
ncp781 www. onsemi.com 8 typical characteristics figure 4. output voltage vs. input voltage at ncp781bmnadjtag figure 5. output voltage vs. input voltage at ncp781bmn033tag input voltage (v) input voltage (v) 140 120 100 80 60 40 20 0 1.220 1.225 1.230 1.235 1.240 1.245 1.250 140 120 100 80 60 40 20 0 3.308 3.312 3.316 3.320 3.324 3.328 3.332 figure 6. output voltage vs. input voltage at ncp781bmn050tag figure 7. output voltage vs. input voltage at NCP781BMN150TAG input voltage (v) input voltage (v) 140 120 100 80 60 40 20 0 4.98 4.99 5.00 5.01 5.02 5.03 5.04 130 110 150 90 70 50 30 10 14.82 14.86 14.90 14.94 14.98 15.02 15.06 output voltage (v) output voltage (v) output voltage (v) output voltage (v) t a = 125 c 85 c 25 c 0 c ?40 c ncp781bmnadjtag v out(nom) = 1.23 v i out = 50 a ncp781bmn033tag v out(nom) = 3.3 v i out = 50 a t a = 125 c 85 c 25 c ?40 c ncp781bmn050tag v out(nom) = 5.0 v i out = 50 a t a = 125 c 85 c 25 c ?40 c NCP781BMN150TAG v out(nom) = 15.0 v i out = 50 a t a = 125 c 85 c 25 c ?40 c figure 8. dropout voltage vs. output current at ncp781bmn033tag output current (ma) 90 80 60 50 40 30 20 10 0 1 2 3 4 5 6 7 dropout voltage (v) t a = 125 c 25 c ?40 c ncp781bmn033tag v out(nom) = 3.3 v 70 100 figure 9. dropout voltage vs. output current at ncp781bmn050tag output current (ma) 100 70 60 50 40 20 10 0 0 1 2 3 4 5 6 7 dropout voltage (v) t a = 125 c 25 c ?40 c ncp781bmn050tag v out(nom) = 5.0 v 30 80 90
ncp781 www. onsemi.com 9 typical characteristics figure 10. dropout voltage vs. output current at NCP781BMN150TAG output current (ma) 90 80 60 50 40 30 10 0 0 1 2 4 5 6 7 9 dropout voltage (v) t a = 125 c 25 c ?40 c NCP781BMN150TAG v out(nom) = 15.0 v 20 70 100 3 8 figure 11. quiescent current vs. input voltage at ncp781bmnadjtag figure 12. quiescent current vs. input voltage at ncp781bmn033tag input voltage (v) input voltage (v) 15 0 120 90 60 30 0 16 18 20 22 24 26 150 120 90 60 30 0 18 20 22 24 26 28 figure 13. quiescent current vs. input voltage at ncp781bmn050tag figure 14. quiescent current vs. input voltage at NCP781BMN150TAG input voltage (v) input voltage (v) 15 0 120 90 60 30 0 18 20 22 24 26 28 150 120 90 60 30 0 18 20 22 24 26 28 quiescent current ( a) quiescent current ( a) quiescent current ( a) quiescent current ( a) t a = 125 c 25 c ?40 c ncp781bmnadjtag c in = c out = 1 f mlcc i out = 0 vin = vena ncp781bmn050tag c in = c out = 1 f mlcc i out = 0 vin = vena NCP781BMN150TAG c in = c out = 1 f mlcc i out = 0, vin = vena ncp781bmn033tag c in = c out = 1 f mlcc i out = 0, vin = vena t a = 125 c 25 c ?40 c t a = 125 c 25 c ?40 c t a = 125 c 25 c ?40 c figure 15. output voltage noise spectral density at ncp781bmn033tag frequency (khz) 100 0 100 10 1 0.1 0.01 0 1 2 3 4 5 6 8 v/ hz 7 c in = c out = 1 f v in = 150 v v out(nom) = 3.3 v i out = 1 ma t a = 25 c
ncp781 www. onsemi.com 10 typical characteristics figure 16. output voltage noise spectral density at ncp781bmn050tag frequency (khz) 1000 100 10 1 0.1 0.01 0 2 4 6 8 10 12 figure 17. output voltage noise spectral density at NCP781BMN150TAG figure 18. output voltage noise spectral density at ncp781bmnadjtag frequency (khz) frequency (khz) 100 0 100 10 1 0.1 0.01 0 10 20 30 40 50 1000 100 10 1 0.1 0.01 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 v/ hz v/ hz v/ hz c in = c out = 1 f v in = 150 v v out(nom) = 15.0 v i out = 1 ma t a = 25 c c in = c out = 1 f v in = 150 v v out(nom) = 1.23 v i out = 1 ma t a = 25 c c in = c out = 1 f v in = 150 v v out(nom) = 5.0 v i out = 1 ma t a = 25 c figure 19. psrr vs. frequency at ncp781bmn033tag frequency (khz) 100 0 100 10 1 0.1 0.01 30 40 50 60 70 80 90 psrr (db) v in = 25 v + 200 mvpp modulation v out(nom) = 3.3 v c out = 1 f mlcc t a = 25 c i out = 1 ma i out = 10 ma i out = 50 ma figure 20. psrr vs. frequency at ncp781bmn050tag frequency (khz) 1000 100 10 1 0.1 0.01 30 40 50 60 70 80 90 psrr (db) v in = 25 v + 200 mvpp modulation v out(nom) = 5.0 v c out = 1 f mlcc t a = 25 c i out = 1 ma i out = 10 ma i out = 50 ma figure 21. psrr vs. frequency at NCP781BMN150TAG frequency (khz) 100 0 100 10 1 0.1 0.01 40 45 50 55 60 65 70 psrr (db) v in = 25 v + 200 mvpp modulation v out(nom) = 15.0 v c out = 1 f mlcc t a = 25 c
ncp781 www. onsemi.com 11 typical characteristics figure 22. psrr vs. frequency at ncp781bmnadjtag frequency (khz) 1000 100 10 1 0.1 0.01 40 50 60 70 80 90 100 psrr (db) v in = 25 v + 200 mvpp modulation v out(nom) = 1.23 v c out = 1 f mlcc t a = 25 c
ncp781 www. onsemi.com 12 applications information the ncp781 is very high input voltage regulator with internal thermal shutdown and internal current limit. t ypical application circuits are shown in figure 23. ncp781 adj c in c out r 1 r 2 1 uf 1 uf vin = 6 v ? 150 v vout = 1.23 v ? 15 v ncp781 fix in en out gnd c in c out 1 uf 1 uf vin = 6 v ? 150 v in en gnd out adj vout = 1.5 v ? 15 v figure 23. typical application circuits enable enable sen input decoupling (c in ) a ceramic or tantalum 0.1 f capacitor is recommended and should be connected close to the ncp781 package. higher capacitance and lower esr will improve the overall line and load transient response. output decoupling (c out ) the ncp781 is a stable component and does not require a minimum equivalent series resistance (esr) for the output capacitor. the minimum output decoupling value is 0.1 f and can be augmented to fulfill stringent load transient requirements. the regulator works with ceramic chip capacitors as well as tantalum devices up to 10 f. the larger values improve noise rejection, load regulation and transient response. enable operation the enable pin will turn the regulator on or off. the threshold limits are covered in the electrical characteristics table in this data sheet. the turn?on/turn?off transient voltage being supplied to the enable pin should exceed a slew rate of 150 mv/ s to ensure correct operation. if the enable function is not to be used then the pin should be connected directly to v in . output voltage adjust the output voltage can be adjusted from 1.23 v to 15 v using resistors between the output and the adj input. the output voltage and resistors are chosen using equation 1 and equation 2. v out 1.23 1 r 1 r 2 i adj r 1 (eq. 1) r 2 r 1 1 v out 1.25 1 (eq. 2) input bias current i adj is typically less than 5 na. choose r1 arbitrarily to minimize errors due to the bias current and to minimize noise contribution to the output voltage. use equation 2 to find the required value for r2. this device does not require a minimal load. thermal considerations as power in the ncp781 increases, it might become necessary to provide some thermal relief. the maximum power dissipation supported by the device is dependent upon board design and layout. mounting pad configuration on the pcb, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. when the ncp781 has good thermal conductivity through the pcb, the junction temperature will be relatively low with high power applications. the maximum dissipation the ncp781 can handle is given by: p d(max)
t j(max) t a r ja (eq. 3) the power dissipated by the ncp781 can be calculated from the following equations: p d v in i gnd @i out i out v in v out (eq. 4) or v in(max) p d(max) v out i out i out i gnd (eq. 5) hints v in and gnd printed circuit board traces should be as wide as possible. when the impedance of these traces is high, there is a chance to pick up noise or cause the regulator to malfunction. place external components, especially the output capacitor, as close as possible to the ncp781, and make traces as short as possible.
ncp781 www. onsemi.com 13 ordering information part no. output voltage (v) marking package shipping ? ncp781bmnadjtag adj 781n badj dfn6 (pb?free) 3000 / tape & reel (contact sales office for availability) ncp781bmn033tag 3.3 781n b033 ncp781bmn050tag 5 781n b050 NCP781BMN150TAG 15 781n b150 ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
ncp781 www. onsemi.com 14 package dimensions case 506df issue b notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.30mm from the terminal tip.. 4. coplanarity applies to the exposed pad as well as the terminals. 5. for device opn containing w option, detail a alternate construction a?2 and detail b alternate construction b?2 are not applicable. a b e d 2x 0.10 c pin one reference top view 2x 0.10 c note 4 a a3 0.08 c 0.05 c c seating plane side view dim min max millimeters a 0.80 0.90 a1 0.00 0.05 a3 0.20 ref b 0.25 0.35 d 3.30 bsc d2 2.55 2.75 e 3.30 bsc e2 1.00 1.20 e 0.65 bsc l 0.35 0.45 l1 0.00 0.15 *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* l1 detail a l alternate constructions l ?? ?? 0.20 ref detail b 1.21 3.60 1.92 0.58 6x 0.40 0.65 pitch 3.50 1 6x dimensions: millimeters package outline recommended d2 e2 bottom view b e 6x 0.10 b 0.05 a c c l 6x note 3 l2 2x 12 3 6 e/2 detail a 3x e 0.10 b a c e3 0.50 bsc on semiconductor and are trademarks of semiconductor components industries, llc dba on semiconductor or its subsidiaries i n the united states and/or other countries. on semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property . a listing of on semiconductor?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf . on semiconductor reserves the right to make changes without further notice to any products herein. on semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does o n semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. buyer is responsible for its products and applications using on semiconductor products, including compliance with all laws, reg ulations and safety requirements or standards, regardless of any support or applications information provided by on semiconductor. ?typical? parameters which may be provided in on semiconductor data sheets and/or specifications can and do vary in dif ferent applications and actual performance may vary over time. all operating parameters, including ?typic als? must be validated for each customer application by customer?s technical experts. on semiconductor does not convey any license under its patent rights nor the right s of others. on semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any fda class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. should buyer purchase or use on semicondu ctor products for any such unintended or unauthorized application, buyer shall indemnify and hold on semiconductor and its officers, employees, subsidiaries, affiliates, and distrib utors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that on semiconductor was negligent regarding the design or manufacture of the part. on semiconductor is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 ncp781/d literature fulfillment : literature distribution center for on semiconductor 19521 e. 32nd pkwy, aurora, colorado 80011 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative ?

▲Up To Search▲

Price & Availability of NCP781BMN150TAG

	To Download NCP781BMN150TAG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .